[WiP] madVR support in MP1 (21 Viewers)

[daWooky]

first only with coreV316 and the old dshowhelper - no mad error anymore with mad v92.1 on start but i had a blacksreen at the end off the second video (mepo was still responsive in the back)...
so i tried with core316 + dshowhelper_V1rev. - no blacksceens so far and playlist seems working fine too.
similar on htpc with mad v91.1 both new were necessary...tv zap seem a bit faster too again

 

[Sebastiii]

Thank
I have done another little change because sometimes on fast playlist, it can lock
Can you try attached zip ?
It's both core and dshowhelper
I hope it's working

 

[daWooky]

yep it can lock, i saw it also on htpc once earlier today.
happened when i switched from live tv to a running recording resulted in the last live tv picture freezed and mepo unresponsive idling but at least no blackscrens
v316B tomorrow

 

[Sebastiii]

Thanks
Also can you do a compare with this one too ?
It seems that i can't reproduce the lock (the zapping between channel from different tuner will be a little slower but if it can avoid the lock

 

[joecrow]

Hope I can be of some help here, I can now run some reasonably comprehensive regression testing on my Desktop as it can now play full HD German TV, so I won't have to disturb my HTPC all the time.
Where would you like me to start?
I'm currently on madvr 0.91 and MP 1.17 final, tried madvr 0.92 but got 100% crash on stop, various vids. OK when I went back to 0.91.
UPDATE:-
I don't use Trakt

 

[Sebastiii]

Great
If you can try V317 bin on top of latest installer in first post with 0.91 and after 0.92 it could be great
Thanks.

 

[Sebastiii]

Hope I can be of some help here, I can now run some reasonably comprehensive regression testing on my Desktop as it can now play full HD German TV, so I won't have to disturb my HTPC all the time.
Where would you like me to start?
I'm currently on madvr 0.91 and MP 1.17 final, tried madvr 0.92 but got 100% crash on stop, various vids. OK when I went back to 0.91.
UPDATE:-
I don't use Trakt

In case of, i have added the full installer in first post

 

[joecrow]

OK using v317 from the first post and madvr 0.91 TV, HD, SD and Elysium vids all play fine also no problems with OV, TV zapping also looks good, 3D not possible on my Desktop hardware but will try tomorrow on my HTPC. Same also all good with Madvr v 0.92.

UNTIL I changed the "Hardware Decoder to use" in LAV from DXAV2 Copy-Back to NVIDIA CLUVID*, see 1st attached screenshot, thereafter whenever I played a video that required upscaling (less that 1080x1920) I got a blackscreen with audio, pressing stop stopped the audio and returned to the previous screen but then MP was then hung and I had to use Task Manager to kill it. I checked the upscaling setting in Madvr and found if I used anything other than NED13, settings as shown in the 2nd screenshot, the problem did not occur. I seem to recall from the release notes of an earlier version of Madvr that there is some restriction with NED13 but can no longer find it, so maybe that is the cause. Just a little worried that with the blackscreen and audio playing I could still go into Madvr setting and change things, so it had not crashed or hung but after hitting stop it was MP that hanged.
The attached logs cover a single hang incident.

*Preferred setting as it fixes this.

 

[Sebastiii]

Yep thanks

So i can if freeze :
[2017-08-22 14:40:05,669] [Log ] [MPMain ] [DEBUG] - VMR9: mediaCtrl.Stop() 1
[2017-08-22 14:40:05,771] [ 0] [ bc8] - MPMadPresenter:topping() m_pMediaControl stop 1

So it get stuck because something wasn't running correctly and a deadlock occurs on stop because it can't stop it.
Hoping it's only related to NVIDIA CUVID !!!!

 

[joecrow]

Hoping it's only related to NVIDIA CUVID !!!!

It does seem to be just with the Nvidia Cluvid, with the same upscaling settings (NED13) it runs all OK with DXVA2 Copy-Back, did not try Native or Intel(no hardware).