Netherlands
I'm going a bit insane because i cannot find a way to get my system to work. First of all, I know i'm in a bit of a gray area. That beeing said i cannot imagine it being of influence in my specific case (if mistaken please enlighten).
I'm using a Asrock 3D vision 137B (Core i3 370 with 4GB ram, nvidia 425 and a ssd disk with two Anysee E30TC USB tunercards) which performs quite good.
I'm using Argus as TV Service and when I play back with VLC player to a HD channel it runs very good, in fact i can watch two HD channels at the same time and the CPU doesn't go over 50% and sound / video is very clear and in sync. To be clear, this is 'watch channel' directly from the argus interface.
When watching those same channels in MePo (just did a fresh install with 1.2.3) with the latest LAV codecs it stutters and i'm getting loads of discontinuty messages in my log files.
Just to be clear, SD channels run just fine, on both tuners.
I'm aware of the mediaportal audio render, the experimental tsreader.ax and dshowfilters, i've already tried all the latest versions and set the registery setting for the audiorender aswell (which is explained in that specific topic).
Everything i do doesn't seem to fix of doesn't even come close to a fix. It only happens with HD television, regular 1080p movies also run fine. In the LAV codec i've enabled the hardware decoding, but have tried numberous of settings, none of them seem to have an affect.
I've seen there are two topics regarding the anysee tuners, one where some DEV claims to have a SDK wheras the topic seems dead. The other is about compailing something from the GITHUB, i don't know nothing about compailing anything so that would be a bit hard for me.
With my previous HTPC which was much slower HD television ran fine. I've even bought new hirschmann cables and amplifiers to exclude the signal strenght (eventhough it works fine with VLC directly from argus).
Is there a way for me to get a pointer to what goes wrong with MePo (for as VLC with argus runs fine), i'm willing to pretty do anything for a solution.
I'm using a Asrock 3D vision 137B (Core i3 370 with 4GB ram, nvidia 425 and a ssd disk with two Anysee E30TC USB tunercards) which performs quite good.
I'm using Argus as TV Service and when I play back with VLC player to a HD channel it runs very good, in fact i can watch two HD channels at the same time and the CPU doesn't go over 50% and sound / video is very clear and in sync. To be clear, this is 'watch channel' directly from the argus interface.
When watching those same channels in MePo (just did a fresh install with 1.2.3) with the latest LAV codecs it stutters and i'm getting loads of discontinuty messages in my log files.
Just to be clear, SD channels run just fine, on both tuners.
I'm aware of the mediaportal audio render, the experimental tsreader.ax and dshowfilters, i've already tried all the latest versions and set the registery setting for the audiorender aswell (which is explained in that specific topic).
Everything i do doesn't seem to fix of doesn't even come close to a fix. It only happens with HD television, regular 1080p movies also run fine. In the LAV codec i've enabled the hardware decoding, but have tried numberous of settings, none of them seem to have an affect.
I've seen there are two topics regarding the anysee tuners, one where some DEV claims to have a SDK wheras the topic seems dead. The other is about compailing something from the GITHUB, i don't know nothing about compailing anything so that would be a bit hard for me.
With my previous HTPC which was much slower HD television ran fine. I've even bought new hirschmann cables and amplifiers to exclude the signal strenght (eventhough it works fine with VLC directly from argus).
Is there a way for me to get a pointer to what goes wrong with MePo (for as VLC with argus runs fine), i'm willing to pretty do anything for a solution.
