CybrDisplay External Status Plugin (4 Viewers)

[rsbrux]

Since this plugin seems destined to replace "External Display", I tried to get it to work on my Scaleo E.
Unfortunately, I couldn't find an entry in the drop-down list capable of writing to its display.
The display is theoretically a Futaba, but this setting doesn't work with "external Display" either, even though the Futaba driver is installed.
What works in "External Display" is the Scaleo EV from David K.
Which display option should I use in CybrMage?

 

[anymohr]

restarting a generic VFD

Hello there! I am using a generic VFD that simply displays the characters that are sent to it. All works fine as long as I do not switch the display off by removing the power. When I switch it on again the init string (x04 x11 x14) is forgotten of course and the data displayed is deranged, the cursor of the display runs over the two lines and the brightness is back to high. Does anyone know how to configure the plugin such that it initializes the display regularily? I have attached the datasheet of the display I am using. Thanks!

 

[chemelli]

1. checked - the external display plugin is disabled!

Delete it. It will not be included in new SVN and this will avoid confusion

2. Without the SG_VFD.dll V3 the VDF does not work!

Install 7.40 build of iMON and leave "AutoDetect" instead of forcing V3 and VFD type.
This seems to work for me.

Simone

 

[elevation1]

If leave autodetect... there is no text on vfd... if leave vfd there is text... why?

 

[globaldonkey]

Because your display cannot be automatically detected. That's why there is an option to specify your display.

 

[elevation1]

but the last version of this plugin is 0.2.3.0? is it possible fix the delay?

with imon manager on "always off" and select these option in plugin cybrdisplay:

ImageShack - Hosting :: pluginjw0.jpg

i have a delay of 10seconds...

p.s. an image is better than more words

 

[Pappmann]

i had delay with the IMON 7.40 Driver,

after i installed IMON 7.20 it was OK.

I work with settings:

Enshure running before driver start [disabled]

Force restart after driver start [disabled]

Force reload during driver start [disabled]

restart Fronview on exit [enabled]

Force to use Keyboard Mode with Imon Pad [disabled]

 

[elevation1]

so the problem is driver 7.20?

p.s. i have the same problemwith driver 7.20

 

[alal]

Some help!

Hi all,

I believe this is an excelent plug-in but I just can't get it to work on my system.
I've got a Thermaltake DH102 with iMON LCD.
Can some one help me out please?

See log for details.

Thanks

 

[chemelli]

Hi all,

I believe this is an excelent plug-in but I just can't get it to work on my system.
I've got a Thermaltake DH102 with iMON LCD.
Can some one help me out please?

See log for details.

Thanks

Hi alal,

from you log:

2008-10-23 23:05:07.198433 [Info.][CybrDisplay]: iMONLCDg.GetDisplayInfoFromFirmware(): Searching for Firmware version = 3414
2008-10-23 23:05:07.199433 [Info.][CybrDisplay]: iMONLCDg.GetDisplayInfoFromFirmware(): version match NOT FOUND
2008-10-23 23:05:07.201433 [Info.][CybrDisplay]: iMONLCDg.Setup(): Hardware tests determined UNSUPPORTED display type!
2008-10-23 23:05:07.202433 [Info.][CybrDisplay]: (IDisplay) iMONLCDg.Setup(): Display Type is NOT SUPPORTED - Plugin disabled

You can try fixing it to LCD or LCD2. Good luck !

Simone