Setting up Comcast Digital Cable Box help (1 Viewer)

Thread starter PKRAJOO
Start date November 7, 2012

PKRAJOO

Guest

November 7, 2012

Hi
I have a tv tuner connected to my computer. Mediaportal recognizes my tv tuner. i have a set top box from comcast. How do I see the comcast channels on mediaportal?

Users who are viewing this thread

Similar threads

MP1 MP2 MP2 - V2.5 Sony Bravia 32S5100 DE

When i was using 2.5, and like im using MP1, i set the resolution of my desktop. And MEPo just uses whatever i have set.

MP 2.5 does not recognize my Bravia 32S5100 as 1920x1080 but only as 1280x720. The PC's monitor is recognized as 1920x1080. Both...

Replies: 2

Views: 776

March 18, 2026

caveman

MP1 MP2 how to record TV and Set top box DE

You can check the MediaPortal forum for a list of compatible TV cards with MP2 and Comcast set-top boxes. The forum has a dedicated section for hardware discussions where users share their experiences. You might also want to look into the official MediaPortal documentation for any specific recommendations on TV cards. Good luck! :)

You can check the MediaPortal forum for a list of compatible TV cards with MP2 and Comcast set-top boxes. The forum has a dedicated...

Q1.) I have installed MP2 on my Windows 10 Pro computer. I have Comcast cable and set top box. Where can I find information about...

Replies: 4

Views: 3K

October 22, 2024

EvaWhirl

MP1 MP2 RTSP - test with VLC on same box, correct syntax? DE

I meant use MP client to try to spot how it's requesting streams for specific channels and then try to do the same with VLC. TV Server development looks dead so I'm afraid you're going to have to figure that out by yourself if it's even possible.

I meant use MP client to try to spot how it's requesting streams for specific channels and then try to do the same with VLC. TV...

Hi everyone, I've set up Mediaportal TV Server on a Windows 11 box, tuner deteced okay, scanned channels, can preview, all seems...

Replies: 8

Views: 1K

March 12, 2026

el Filou

MP1 MP2 How to get MP2 to work with Hauppauge WinTV 1850 TV card DE

I also have never used a set-top box with MP, but I think that you need to use an IR emitter (aka "IR blaster"). The IRSS software controls the emitter, and transmits IR signals under the direction of MP. The IR signal is received by the IR receiver within the set-top box, and so can be used to change channel and so on. The set-top...

I also have never used a set-top box with MP, but I think that you need to use an IR emitter (aka "IR blaster"). The IRSS software...

My computer is running Windows 10 Pro. I have installed MP2. Not sure what version. I have a Hauppauge WinTV 1850 TV card...

Replies: 8

Views: 3K

September 5, 2024

CyberSimian

MP1 MP2 Scanning & Mapping channels DE

I note that you are using MP2. The following applies to MP1, but I think that MP2 is identical in this situation. "TV Server Config" has a "TV Mapping" panel in the "TV Channels" section. On the "TV Mapping" tab: The left column lists the channels that have not yet been mapped to the TV tuner identified by the drop-down menu just...

I note that you are using MP2. The following applies to MP1, but I think that MP2 is identical in this situation. "TV Server...

I've scanned for channels, and got all channels mapped to tuner 0 of my 8 channel TV card (eg: 2 cards of 4 channels each) Is there...