where I can get Example code (1 Viewer)

Thread starter arogerm
Start date April 13, 2007

arogerm

New Member

April 13, 2007

where I can get Example code for TVEngine3 for change Quality record on a Hauppage card?.

are some place for get example of recording more than ona channel on a DVB-T card?.

Thanks

Users who are viewing this thread

Similar threads

MP1 MP2 RTSP - test with VLC on same box, correct syntax? DE

I meant use MP client to try to spot how it's requesting streams for specific channels and then try to do the same with VLC. TV Server development looks dead so I'm afraid you're going to have to figure that out by yourself if it's even possible.

I meant use MP client to try to spot how it's requesting streams for specific channels and then try to do the same with VLC. TV...

Hi everyone, I've set up Mediaportal TV Server on a Windows 11 box, tuner deteced okay, scanned channels, can preview, all seems...

Replies: 8

Views: 1K

March 12, 2026

el Filou

MP1 MP2 Anyone using SiliconDust HDHomeRun Flex Quatro 4? DE

I currently have two Quatros running, one connect, one duo using OTA antennae, mostly UHF fringe area, mostly cat5 local network. Hauppauge card retired long ago. I have also retired very early SD units, the Quatros seem to work much better than the older units. Go to SD's support website and download and install the windows...

I currently have two Quatros running, one connect, one duo using OTA antennae, mostly UHF fringe area, mostly cat5 local network...

I am currently using a Hauppauge WinTV QuadHD PCIe card on MP1 (1.37) for DVB-T, but 2 of the tuners have died. Thinking about...

Replies: 3

Views: 1K

January 30, 2026

tarrow

MP1 MP2 An installation report - older hardware and why I used 1.33 not 1.38 DE

4.5 is really old. I'm not sure 4.5.5 even is a version that actually existed. You should be able to install .NET Framework 4.8.0 on Windows 7 SP1

4.5 is really old. I'm not sure 4.5.5 even is a version that actually existed. You should be able to install .NET Framework 4.8.0...

My TV PC is more a cast-off on older hardware (a 'Quiet PC' i5 4690, 16GB ram, 2xSSD 1xHDD, system graphics), mainly as a cheap way...

Replies: 5

Views: 2K

December 30, 2025

el Filou

MP1 MP2 Picture-in-picture DE

Can anyone tell me the step-by-step procedure for bringing up a second channel in pip mode? I can only do it sometimes, after many tries, and it’s not clear what I am doing that makes it work on those occasions when it does. Cannot find guidance on the site. Thanks, N. Again, if anyone knows how to do this, would be much...

Can anyone tell me the step-by-step procedure for bringing up a second channel in pip mode? I can only do it sometimes, after many...

Replies: 0

Views: 2K

July 23, 2025

Nordfinn

MP1 MP2 Scanning & Mapping channels DE

I note that you are using MP2. The following applies to MP1, but I think that MP2 is identical in this situation. "TV Server Config" has a "TV Mapping" panel in the "TV Channels" section. On the "TV Mapping" tab: The left column lists the channels that have not yet been mapped to the TV tuner identified by the drop-down menu just...

I note that you are using MP2. The following applies to MP1, but I think that MP2 is identical in this situation. "TV Server...

I've scanned for channels, and got all channels mapped to tuner 0 of my 8 channel TV card (eg: 2 cards of 4 channels each) Is there...