United States of America
I know there is a default aspect ratio setting in the general TV setup. Could there be a place to set the default aspect ratio for each channel in the channel config?
Aspect ratio setting (1 Viewer)
- Thread starter marshall
- Start date
please xplain what you are trying to do or what your problem is and maybe there is a solution
- Thread starter
- #4
I can make sure it is on "default" this evening. As I was trying, it was either that or "normal" that was best. However, there is still one station where the people's heads look a bit too elongated unless it is set to "stretch". It would be nice if I could set the AR for just that one channel.
I'm not sure if it has anything to do with it, but I am running at 1680x1050 resolution, which is 16:10 not 16:9. Also, the channel in question is digital.
I'm not sure if it has anything to do with it, but I am running at 1680x1050 resolution, which is 16:10 not 16:9. Also, the channel in question is digital.
you may need to adjust your screen calibration (through MP Setup). This was my issue (people were short and fat)
- Thread starter
- #6
I thought "default" sounded a bit funny, just to make sure, this is the same as "Original Source Format" right?
I'll try the screen calibration too.
I'll try the screen calibration too.
i have had the same problem that yours.
I Live in france and watch DVB-T Channels. The only one i watch which is sending a wide signal is NRJ12.
The first time i set up mp, all was fine exept this channel that was presented with a wrong ar. I took me some time to understand that its a codec problem.
I went to mp setup/TV/Codec, and put there the codecs bundled with my DVBT Board (the codecs are 'intervideo for hauppauge non css', or smthing like that). Once done, all channels were ok, even nrj12 !
Good luck !
I Live in france and watch DVB-T Channels. The only one i watch which is sending a wide signal is NRJ12.
The first time i set up mp, all was fine exept this channel that was presented with a wrong ar. I took me some time to understand that its a codec problem.
I went to mp setup/TV/Codec, and put there the codecs bundled with my DVBT Board (the codecs are 'intervideo for hauppauge non css', or smthing like that). Once done, all channels were ok, even nrj12 !
Good luck !
when people understand this, the world will be a better place
Users who are viewing this thread
Similar threads
I don't know about MP2 but as you said you tried MP1 too, how is the MP music config ?
MP(1) will only use LAV if you select "Internal DirectShow player" as music output, but then you lose gapless playback.
If you you don't have multichannel music you can choose WASAPI as the output and set the number of speakers to stereo.
I have...
I don't know about MP2 but as you said you tried MP1 too, how is the MP music config ?
MP(1) will only use LAV if you select...
Not sure if this a a bug/config/settings problem.
I am running a media portal 2.5 server with 2.41 client but it seems I get the...
If you use "Manual Booking" (left side menu on the "Recording Schedule" panel), you can schedule a recording duration of up to 24 hours. However...
That is using the "conventional" TV sources, i.e. a DVB-T tuner, a DVB-S tuner, or an analogue tuner. You stated in your other thread that you are using an IPTV source. Perhaps there is a...
If you use "Manual Booking" (left side menu on the "Recording Schedule" panel), you can schedule a recording duration of up to 24...
Is there a limit to recording length? My TVServer recordings all cut off at 3 hours but I can't find a setting anywhere to change...
I note that you are using MP2. The following applies to MP1, but I think that MP2 is identical in this situation.
"TV Server Config" has a "TV Mapping" panel in the "TV Channels" section. On the "TV Mapping" tab:
The left column lists the channels that have not yet been mapped to the TV tuner identified by the drop-down menu just...
I note that you are using MP2. The following applies to MP1, but I think that MP2 is identical in this situation.
"TV Server...
I've scanned for channels, and got all channels mapped to tuner 0 of my 8 channel TV card (eg: 2 cards of 4 channels each)
Is there...
Got it.:)
I clicked on the box highlighted in the attached screenshot and also added English GB to that and removed the existing English EN. Misspellled words (like that one) are now underlined with red wavy line.:)
Got it.:)
I clicked on the box highlighted in the attached screenshot and also added English GB to that and removed the existing...
Up untill recently I'm sure there was a spell checker on new posts, (misspelled words were highlighted). It does not seem to be...
I installed the new EXE on my MP 1.36 64-bit system (Win 10 laptop), and... it works fine. (y) :)
Thank you for making this change :). I hope that it will be included in the next release.
-- from CyberSimian in the UK
I installed the new EXE on my MP 1.36 64-bit system (Win 10 laptop), and... it works fine. (y) :)
Thank you for making this...
In "MP Config" the following setting enables the display of channel numbers in the TV EPG:
But there is no equivalent setting in...