Can't find my PCTV 110i (1 Viewer)
- Thread starter NeoGeo
- Start date
- November 14, 2006
- 10
- 0
- Home Country
-
Hungary
Small help: http://wiki.team-mediaportal.com/Add_TVCard_to_natively_supported_list
On mycomputer/Properties/Hardware/Devices you can found your capture card. On properties you can found VEN_...&DEV_...&SUBSYS_...&REV_..
Compare it with CaptureCardDefinitions.xml
Find:
<capturecard commercialname="Pinnacle PCTV 110i" capturename="Pinnacle PCTV 110i BDA Analog Capture" devid="ven_1131&dev_7133&subsys_002e11bd&rev_d0">
(here "&" = "&" not change it
)
If something is not same, then you can make small thing. On XML change that numbers which is not same. It's not to correct thing, but your card can work with Mediaportal.
On mycomputer/Properties/Hardware/Devices you can found your capture card. On properties you can found VEN_...&DEV_...&SUBSYS_...&REV_..
Compare it with CaptureCardDefinitions.xml
Find:
<capturecard commercialname="Pinnacle PCTV 110i" capturename="Pinnacle PCTV 110i BDA Analog Capture" devid="ven_1131&dev_7133&subsys_002e11bd&rev_d0">
(here "&" = "&" not change it
)If something is not same, then you can make small thing. On XML change that numbers which is not same. It's not to correct thing, but your card can work with Mediaportal.
- October 19, 2006
- 39
- 0
- Home Country
-
Netherlands
You have to check your hardware devices in start->configuration->system->tab hardware->device manager.
It probably shows your 110i as an yellow ?
Then put in your pinnacle media center cd and in the device manager right-click to update the drivers.
Then it will install the drivers from cd and MP should detect the tv card.
For watching live tv you have to install an mpeg2 ENcoder, otherwise you get the message: unable to create graph.
I have an 110i working including the remote, but at the moment i'm running windows MCE 2005 because in MP the live tv has a memory leak/crashes and audio is mostly out of sync.
It probably shows your 110i as an yellow ?
Then put in your pinnacle media center cd and in the device manager right-click to update the drivers.
Then it will install the drivers from cd and MP should detect the tv card.
For watching live tv you have to install an mpeg2 ENcoder, otherwise you get the message: unable to create graph.
I have an 110i working including the remote, but at the moment i'm running windows MCE 2005 because in MP the live tv has a memory leak/crashes and audio is mostly out of sync.
Users who are viewing this thread
Similar threads
If you use "Manual Booking" (left side menu on the "Recording Schedule" panel), you can schedule a recording duration of up to 24 hours. However...
That is using the "conventional" TV sources, i.e. a DVB-T tuner, a DVB-S tuner, or an analogue tuner. You stated in your other thread that you are using an IPTV source. Perhaps there is a...
If you use "Manual Booking" (left side menu on the "Recording Schedule" panel), you can schedule a recording duration of up to 24...
Is there a limit to recording length? My TVServer recordings all cut off at 3 hours but I can't find a setting anywhere to change...
MP1
MP2
1.38
Running TVService as "NT Service\TVService" or "Local Service" not working anymore since Windows September 2025 updates
DE
Reading through your code, I can see it's more than a couple steps above my paygrade. :cry:
Reading through your code, I can see it's more than a couple steps above my paygrade. :cry:
I used to run the TVService under the "NT Service\TVService" account to follow least privileges principal (not exposing my whole...
I am following the official documentation for setting up the Kodi plugin in media portal. I have got no issues with media portal, nor media portal plugin on Kodi, but with the Kodi plugin that must be installed in the media portal, as it is not getting detected.
I have made a copy of the dll file into the plugins folder as found in my...
I am following the official documentation for setting up the Kodi plugin in media portal. I have got no issues with media portal...
I am following the official documentation for setting up the Kodi plugin in media portal. I have got no issues with media portal...
I don't know about MP2 but as you said you tried MP1 too, how is the MP music config ?
MP(1) will only use LAV if you select "Internal DirectShow player" as music output, but then you lose gapless playback.
If you you don't have multichannel music you can choose WASAPI as the output and set the number of speakers to stereo.
I have...
I don't know about MP2 but as you said you tried MP1 too, how is the MP music config ?
MP(1) will only use LAV if you select...
Not sure if this a a bug/config/settings problem.
I am running a media portal 2.5 server with 2.41 client but it seems I get the...
Sorted, it is a Rating flag that I have never seen before, silly me !!
Cheers Tony
Sorted, it is a Rating flag that I have never seen before, silly me !!
Cheers Tony
I have just done a clean install of v1.36.
Current setup
Media Portal 1.36
Titan skin (only classic home)
TV Series 4.5.1.737...