MediaPortal SVN-Snapshot:-03-07-2009 01-58h - Revision:21864.rar (2 Viewers)

[xvffx]

Unfortunently a rescan didnt help.

But after searching through the forum i found a solution. Apparently the channelscanner saves wrong networkids for all my channels. They have a networkid of 0 og 40 in the channeldatabase, but the real networkid (as reported but the EPG grabber) is 0xFE00/65024.

After changing it for all the channels i finally get my EPG

Kind regards.
- Martin RIx

I wouldn't call it fixed.. more like a work around.

from my understanding is, this is being worked on... did I assume correct, Gmux ?

 

[Der_Bub]

2009-03-12 19:45:31.421875 [Info.][MPMain]: ExamineVolume: Unknown media type inserted into drive M:
2009-03-12 19:45:31.421875 [Info.][MPMain]: ExamineCD: Unknown media type inserted into drive M:

Try removing the IDE cable from the drive, maybe the drive is starting to fail appart? Also, are you using some CD-writing soft that could have installed own drivers?

12-03-2009 18:18:40.921 [3f4]Video Continuity error... b ( prev 9 )
12-03-2009 18:18:40.921 [3f4]Audio Continuity error... e ( prev 2 )

What's wrong?

The latter indicates weak reception.

After going back to MediaPortal SVN-Snapshot:-02-28-2009 00-07h - Revision:21813 I don't have any Problems with TV! But still many entries in the log files like before. So will look at the adjustment of the satelite dish.

But don't have an Idea what to do with the

2009-03-13 08:00:53.750000 [Info.][MPMain]: ExamineVolume: Unknown media type inserted into drive M:
2009-03-13 08:00:53.765625 [Info.][MPMain]: ExamineCD: Unknown media type inserted into drive M:
2009-03-13 08:00:53.765625 [Info.][MPMain]: NEWAutostart.OnMessage: CD inserted
2009-03-13 08:00:53.765625 [Info.][MPMain]: NEWAutostart.OnMessage: CD inserted
2009-03-13 08:00:53.765625 [Info.][MPMain]: NEWAutostart.OnMessage: CD inserted
2009-03-13 08:00:53.765625 [Info.][MPMain]: NEWAutostart.OnMessage: CD inserted
2009-03-13 08:00:53.765625 [Info.][MPMain]: NEWAutostart.OnMessage: CD inserted
2009-03-13 08:00:54.000000 [Info.][22]: volume removed drive M:
2009-03-13 08:00:54.000000 [Info.][22]: media removed from drive M:
2009-03-13 08:01:13.718750 [Info.][22]: volume inserted drive M:
2009-03-13 08:01:13.718750 [Info.][22]: media inserted in drive M:

Problem.

 

[neilk]

Analog TV - no channel change possible in this svn

With this SVN I’m still experiencing problems with analog channel change on the client not working correctly. This is the problem:

1) On client start TV…. At this point there is no problem, TV works just fine…
2) Select a different channel….now a few seconds goes by with only a black screen, after which an still image comes on…therefore TV looks frozen.
3) On my remote I hit the FFW button…All of a sudden the channel changes and TV works like normal.
4) Now select a different channel, and the problem starts over again until I hit the FFW button….

Also might be important is to mention that I'm not using analog frequencies, but s-video input with IR-blasters..

My problems all started with “SVN-Snapshot:-02-28-2009 00-07h - Revision:21813”, when “Zapping, RTSP improvements” and the “TvGuide got an improvement to switch between channel groups” changes were added.

Logs attached….

I think I'm experiencing a similar issue, using TVE3 Singleseat installation & 2 x Hauppauge PVR150 tuner cards. The svn from the 10/02/2009 works fine. When starting TV for the 1st time, any channel starts, but when I change a channel, I get a black screen for +- 7 seconds, then the last frame of the previous channel reappears. I can stop TV and then start again on the desired channel.

This behaviour also causes no recordings to start (unless it was tuned to the channel that should record before the recording starts)

I have attached logs, reverting back to 10/02/2009 SVN

Regards

Neil

 

[geov]

With this SVN I’m still experiencing problems with analog channel change on the client not working correctly. This is the problem:

1) On client start TV…. At this point there is no problem, TV works just fine…
2) Select a different channel….now a few seconds goes by with only a black screen, after which an still image comes on…therefore TV looks frozen.
3) On my remote I hit the FFW button…All of a sudden the channel changes and TV works like normal.
4) Now select a different channel, and the problem starts over again until I hit the FFW button….

Also might be important is to mention that I'm not using analog frequencies, but s-video input with IR-blasters..

My problems all started with “SVN-Snapshot:-02-28-2009 00-07h - Revision:21813”, when “Zapping, RTSP improvements” and the “TvGuide got an improvement to switch between channel groups” changes were added.

Logs attached….

I think I'm experiencing a similar issue, using TVE3 Singleseat installation & 2 x Hauppauge PVR150 tuner cards. The svn from the 10/02/2009 works fine. When starting TV for the 1st time, any channel starts, but when I change a channel, I get a black screen for +- 7 seconds, then the last frame of the previous channel reappears. I can stop TV and then start again on the desired channel.

This behaviour also causes no recordings to start (unless it was tuned to the channel that should record before the recording starts)

I have attached logs, reverting back to 10/02/2009 SVN

Regards

Neil

Yes, this sounds like the same problem. This problem has been confirmed in the post below...so the dev's are working on it.

https://forum.team-mediaportal.com/1-0-final-svn-builds-302/issues-changing-channels-56161/\

 

[framug]

Yes, this sounds like the same problem. This problem has been confirmed in the post below.

hmm, I just curious to see if idea I posted here https://forum.team-mediaportal.com/...9-12-22h-revision-21720-rar-54862/index9.html could fix your problem or not.

 

[DJBlu]

ATTN Devs,

Reference the Network ID problem,

Not as simple as that I'm affraid. Still getting errors.

No network ID on channel scan. DVB-S that is

Okay I can now see why the NID on the scan isn't working.

In the PATParser.cpp the following is commented out.

// info.NetworkId=sdtInfo.NetworkId;
// info.TransportId=sdtInfo.TransportId;

Just wondering whats the reason for these comments as there is no where else these values are set.

 

[chemelli]

If I select to stop the service in the Server config util, it happens pretty quickly, & the button changes labels to 'start service'. There are no related errors generated in errors.log. If the comskip server plugin was loaded at launch of the service though, problems occur. When selecting to stop the service, there is a substantial delay in the button switching labels to 'start service', & the following lines are logged in errors.log

2009-03-10 19:01:05.373583 [10]: Exception ystem.ArgumentException: Service TvEngine.Events.ITvServerEvent is not registered
at TvLibrary.Interfaces.ServiceProvider.Get[T]()
at TvEngine.ComSkipLauncher.Stop()
at TvService.Service1.StopPlugins()
Exception ervice TvEngine.Events.ITvServerEvent is not registered
site :T Get[T]()
source :TvLibrary.Interfaces
stacktrace: at TvLibrary.Interfaces.ServiceProvider.Get[T]()
at TvEngine.ComSkipLauncher.Stop()
at TvService.Service1.StopPlugins()

In mantis: 0002044: After stopping tvservice error log has exception entries from plugins - MediaPortal Bugtracker
and fixed

for reporting

Simone

 

[SilentException]

Analog giving me huge problems.. When trying to timeshift from TVServerConfig i get "Unknown error occurred" every now and then.. After that, TV service is shut down and i have to manually restart it

+Logs attached..

edit: just one more question..can anyone tell me what are default settings on attached screen in tvserverconfig..thank you!

 

[wonkyd]

ATTN Devs,

Reference the Network ID problem,

Not as simple as that I'm affraid. Still getting errors.

No network ID on channel scan. DVB-S that is

Okay I can now see why the NID on the scan isn't working.

In the PATParser.cpp the following is commented out.

// info.NetworkId=sdtInfo.NetworkId;
// info.TransportId=sdtInfo.TransportId;

Just wondering whats the reason for these comments as there is no where else these values are set.

Would this explain why when I do a DVB-T scan I get no LCNs or EPG with this SVN?

Edit: Looks like that's a no. Just rescanned using DJBlu's TSWriter with that put back in and it still gives me LCNs of 10000 for all muxes with this SVN.

Logs are attached.

 

[flokel]

edit: just one more question..can anyone tell me what are default settings on attached screen in tvserverconfig..thank you!

what you have there, are the default settings