Which tv-card best for component-in (1 Viewer)

butcher9999

New Member
January 6, 2008
4
0
Hi

I need a good tv-card that (without problems) can receive component in using MP. Presently i have haupage 150 but can receive component in using VistaMC but not in MP.

Thx
 

Spragleknas

Moderator
  • Team MediaPortal
  • December 21, 2005
    9,474
    1,822
    Located
    Home Country
    Norway Norway
    Hi again :)
    Are you sure you are referring to component? I believe you are referring to composite.

    I don't know any other cards that accept component in other than SweetSpot (or rebrands). These willprobably be har to get to work in MP - and impossible in VMC?
     

    geov

    MP Donator
  • Premium Supporter
  • November 1, 2006
    756
    38
    Cape Town
    Home Country
    South Africa South Africa
    Hi Spragleknas

    I believe there is now a card that supports "component" but it is not supported by MediaPortal. I've been looking at the "Compro VideoMate E800 PCI Express", but have not purchased it because I use TV2 and I'm worried that I'm going to struggle to get it to work with MediaPortal.

    Here is the link to the product:
    http://www.comprousa.com/New/en/product/e800/e800.html
     

    Users who are viewing this thread


    Write your reply...

    Similar threads

    Thanks for that. I'll give it a try.
    Thanks for that. I'll give it a try.
    I was wondering whether anyone could recommend a specification for dedicated MP1 client machines where we get the best bang for...
    Replies
    27
    Views
    3K
    I did a check of MP 1.36 x64 on Win11 and I can confirm, that the TV server correctly detects running MediaPortal.exe process.
    I did a check of MP 1.36 x64 on Win11 and I can confirm, that the TV server correctly detects running MediaPortal.exe process.
    Hi, I am using MP in a client-only setup including DVB-S card for over 10 years now. And regularily scheduling records waking up...
    Replies
    9
    Views
    859
    Apologies Pablik. My bad. I neglected to run WMI Manager and check Properties as you advised. Sure enough, it produced this error: I tried to run winmgmt /resetrepository, but there were conflicts with running services. So I stopped those services (Malwarebytes & IP Helper), then stopped the winmgmt service. I was then able to run...
    Apologies Pablik. My bad. I neglected to run WMI Manager and check Properties as you advised. Sure enough, it produced this error...
    Hi, Was using v1.33 without issue. Then started receiving error message "Unknown error occurred" when trying to watch TV. Upgraded...
    Replies
    7
    Views
    716
    Ok, so perhaps a solution, but not the "right" solution. On the client, within media portal configuration, under TV settings, advanced options, I switched to UNC paths instead of the default RSS, and it's working very well. Sure I had to figure out the paths, but no big deal. Maybe helpful for someone in the future. Thanks for the...
    Ok, so perhaps a solution, but not the "right" solution. On the client, within media portal configuration, under TV settings...
    Hi folks. I have an issue with a new install/integration into my mediaportal system. I have a “mediaportal server” which has the TV...
    Replies
    5
    Views
    892
    MP1 MP2 MP2 - V2.5 No Thumbnails for TV recordings DE
    I know, missing thumbnails for TV recordings have been discussed before. But even after tryping to follow possible solutions provided by the forum, the problem persists. In short, I am running MP 2.5 on a Win11 system with the skin blue vision (I also tried WMC but same issue). When recording TV shows no thumbnails are created. I have...
    I know, missing thumbnails for TV recordings have been discussed before. But even after tryping to follow possible solutions...
    I know, missing thumbnails for TV recordings have been discussed before. But even after tryping to follow possible solutions...
    Replies
    0
    Views
    321
    Top Bottom