Raid solutions (1 Viewer)

lostinohio

Portal Member
October 19, 2007
5
0
Home Country
United States of America United States of America
So what are you doing to protect your movies?

I have about 1 Tb of movies on hard drives and it dawned on me that if I had a drive failure I would be one sad puppy. So can anyone recommend a raid solution?
 

funbobbee

Portal Member
August 8, 2007
6
0
RAID 5 all the way baby...

I bought a silicon image pci raid card that does RAID 5 for about £20 (see below for example)

http://cgi.ebay.co.uk/Silicon-Image...ryZ96881QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

It takes 4 sata 150 drives and is recognised by windows without having to get drivers from the website (which are available if you need them)

4 x 250Gb sata drives gives you about 750Gb of storage. The resaon for the loss is that with RAID 5, if you have a disk failure, you can swap out the faulty drive, do a rebuild (very easy) and job done. No data loss...

The best thing about these cards is that if you have a system failure (my motherboard blew up in December!!!) you just plug the card into the new motherboard and away you go... NO DATA LOSS...

There are other cards available (check out the XFX raid 3 card which is similar, but is meant to read/write quicker and takes sata 300 disks), but for price and ease of use I don't think you can go wrong.
 

UNOPARATOR

MP Donator
  • Premium Supporter
  • September 19, 2007
    231
    70
    Istanbul
    Home Country
    Turkey Turkey
    I have a RAID5 array with 8x 500GB drives on a PCI-Express 4x (Highpoint-tech RocketRAID 2320) addon card.
    The only the thing you should worry is more than 1 disks goes bad at the same time which results total data loss for all the disks or partition failures.
    Also you need a GTP partition (not bootable) if you'ld like to have a single partition > 2TB ;) which is supported on Windows XP Pro x64, Windows Server 2003 and Windows Vista (not supported on 32bit WinXP)...
     

    lostinohio

    Portal Member
    October 19, 2007
    5
    0
    Home Country
    United States of America United States of America
    That is too funny unoparator.. That is the raid card I was looking at. I will probably order it today. I already spoke with Highpoint support and they will support 1TB drives.
     

    AlcoNaft

    Portal Member
    October 17, 2007
    11
    1
    Home Country
    Norway Norway
    2lostinohio - It also possible to use software RAID5 built-in into Windows Server. Also it is possible to patch Windows XP to get this functionality. In general there are 3 type of RAID controllers:

    1) Hardware - prices starts from 300$, more than mobo :)
    2) Hardware/Software - price about 30-40$
    3) Software - built-in into Windows Server, or *nux.

    The second type is rubbish, because all calculations of checksum made by supplied drivers. You can use it as SATA port extender (if you don’t have enough on the mobo), actually it is a port extender with small BIOS and set of drivers.

    I suggest to use 1 option or 3. Please note, if you use Windows Software-RAID, you can migrate from one mobo to another without any problem. But if RAID-controller died - you will have to find exactly the same model in order to restore data.
     

    Users who are viewing this thread

    Similar threads

    MP1 MP2 Case Downsizing DE
    Most (all?) small PC cases accept only ITX motherboards, which have only one PCI-E slot. So you could install only one PCI-E tuner card. A quad-tuner card would give you four tuners, but if you wanted more tuners you would need to use the TBS eight-tuner card, or use external tuners, either USB tuners (available with single or dual...
    Most (all?) small PC cases accept only ITX motherboards, which have only one PCI-E slot. So you could install only one PCI-E tuner...
    I've been using MP2 now for about 3 years: I really happy with the way it works, although I can think of many great features I'd...
    Replies
    1
    Views
    396
    Just those I attached. I messed about with task priorities MP/TV-Server/SQL-Server and the issue changed to the skin.. I would do something, but it would be 10's of seconds before the action happened. Doing an Alt-Tab would flush the actions. Too weird lol!! So, with some flak from the family, I had to give in. I just did a...
    Just those I attached. I messed about with task priorities MP/TV-Server/SQL-Server and the issue changed to the skin.. I would do...
    So, this one has me quite stumped. Have tried ) and a few things - driver updates, kicking the box, threatening it with a static...
    Replies
    8
    Views
    818
    Ok, so perhaps a solution, but not the "right" solution. On the client, within media portal configuration, under TV settings, advanced options, I switched to UNC paths instead of the default RSS, and it's working very well. Sure I had to figure out the paths, but no big deal. Maybe helpful for someone in the future. Thanks for the...
    Ok, so perhaps a solution, but not the "right" solution. On the client, within media portal configuration, under TV settings...
    Hi folks. I have an issue with a new install/integration into my mediaportal system. I have a “mediaportal server” which has the TV...
    Replies
    5
    Views
    502
    OK, I found a way to make it work. It seems like MP-TV-series Configuration (and Moving Pictures Configuration) starts as Administrator, and the Administrator do not have yet logged in on the UNC \\192.168.222.247\Public even if the normal user on the PC have done it. So to fix it on the Win 11 HTPC: Created a shortcut to...
    OK, I found a way to make it work. It seems like MP-TV-series Configuration (and Moving Pictures Configuration) starts as...
    Hi! I was running MP1.33 x64 and I was fine and happy since many years, then the hard drive on the HTPC died. But I was able to...
    Replies
    1
    Views
    801
    Due to the recent update in FanartHandler and using dynamic paths for the ClearArt, ClearLogo and CDArt this is resolved without the need to update MovingPictures Cornerstone.MP.Extensions as FH no longer uses #selecteditem and instead uses #MovingPictures.SelectedMovie.title. At the moment MePo theme has these values but I plan to...
    Due to the recent update in FanartHandler and using dynamic paths for the ClearArt, ClearLogo and CDArt this is resolved without...
    There is an issue with missing #fanarthandler.movie.clearart.selected path value when MovingPictures loads a list of movies. When...
    Replies
    1
    Views
    801
    Top Bottom