Signal level & signal quality (1 Viewer)
- Thread starter LukasCh
- Start date
Czech Republic
Signal level\quality is affected by the TVCard manufacturers driver, so by no means 100% accurate.
Take it you cannot view this channel, if the rest of your dvb channels show quality above 30% and they work, then it will be down to incoming signal too weak, this would not stop a settop box from being able to receive channels as they are better at handling weak signals anyway.
- Thread starter
- #3
My TV card Club 3D Zap TV 2202 (hybrid) has BDA drivers. I can see TV programs on one multiplex (626 MHz) signal quality lightly above 30%, bud i cannot see the second multiplex (506MHz) in my region because the signal quality is under 30%. Somethimes i canot find this multiplex in autoscan. The signal level is zero in both multiplexes. Both are the same tramsmitter (same place, same power). Maybe the fault is in my antena wall plug, because the wall plugs was changed in my flat (because of digital receiving). So someway i have to measure the signal level.
The only way to find if there is a problem, check with neighbours firstly, can they receive signals fine with no weather breakup, ie hard rain\wind. if they have good signal, then its your incoming signal at fault, so check any aerial connections that your comfortable dealing with, if not get a aerial installer to check incoming signal quality and advise you on what to do to improve the signal strength.
Users who are viewing this thread
Similar threads
Hello,
Name need to be the same as computer name.
Also, logs could be useful.
Hello,
Name need to be the same as computer name.
Also, logs could be useful.
It is a bit of a long story!
I successfully installed MP2 on my old PC as client/server with client on my laptop to confirm my...
Well, the log doesn't show any problems. I can see correctly tuned channels in the log. It seems to me that the tuner works fine.
Can you copy the created ts file(located in your timeshift folder) somewhere else while in channel preview and try to play it in VLC or MPC-HC?
PS: You can also try to make short record
Well, the log doesn't show any problems. I can see correctly tuned channels in the log. It seems to me that the tuner works fine...
I've been successfully using MediaPortal1 and TV Server 1.17 on Win7 for years, using first a HDHomerun tuner, when that died, a...
MP1
MP2
1.38
Running TVService as "NT Service\TVService" or "Local Service" not working anymore since Windows September 2025 updates
DE
Reading through your code, I can see it's more than a couple steps above my paygrade. :cry:
Reading through your code, I can see it's more than a couple steps above my paygrade. :cry:
I used to run the TVService under the "NT Service\TVService" account to follow least privileges principal (not exposing my whole...
Thank you for pointing out that my analysis may be less than accurate. :eek: :p
Although the change to TV channel 71 may not also have been applied to the independent radio channels (different MUXes), the logs that I prepared for one of the development team does show a difference between channel 704 ("BBC Radio 4") and channel 731...
Thank you for pointing out that my analysis may be less than accurate. :eek: :p
Although the change to TV channel 71 may not also...
I have just discovered that I can no longer receive any of the independent radio channels broadcast on DVB-T in the UK. In...
Perhaps... Only way to confirm would be for me to invest in a different USB DVB-S2 tuner (like the Hauppauge WinTV-NOVA-S2), which I might do if the issue persists.
Perhaps... Only way to confirm would be for me to invest in a different USB DVB-S2 tuner (like the Hauppauge WinTV-NOVA-S2), which...
I have a dedicated TV Server x64 v1.36 running on Windows 11, with a Hauppauge WinTV-dualHD tuner for DVB-T channels (Freeview) and...