Turn On TV with Remote (1 Viewer)
- Thread starter CGT
- Start date
- December 6, 2010
- 125
- 32
- Home Country
-
Germany
Depends on the TV. My Sharp turns on. It's easy to test; turn the TV on, then unplug the TV. After a short time plug it again and see in what state it will go... ;-)
Maybe there is a difference if there is a signal to the TV or not...
Maybe there is a difference if there is a signal to the TV or not...
- December 6, 2010
- 125
- 32
- Home Country
-
Germany
Why should it be bad? I didn't think so.
I turn my TV on/ off with the master/ slave and everything is fine here
I turn my TV on/ off with the master/ slave and everything is fine here
Have you seen this; http://www.pulse-eight.com/store/products/104-usb-hdmi-cec-adapter.aspx
Also a topic here; https://forum.team-mediaportal.com/...rol-mediaportal-using-your-tvs-remote.114029/
True you need a compatible tv but it looks good, ordered one and will test soon
Also a topic here; https://forum.team-mediaportal.com/...rol-mediaportal-using-your-tvs-remote.114029/
True you need a compatible tv but it looks good, ordered one and will test soon
Users who are viewing this thread
Similar threads
Sorry i dont use Mov Pic
Sorry i dont use Mov Pic
Hi, I have done this previously but have just done a fresh install of MP1 (1.34 X64) and for the life of me can't see how to do it...
Ok, so perhaps a solution, but not the "right" solution. On the client, within media portal configuration, under TV settings, advanced options, I switched to UNC paths instead of the default RSS, and it's working very well. Sure I had to figure out the paths, but no big deal.
Maybe helpful for someone in the future. Thanks for the...
Ok, so perhaps a solution, but not the "right" solution. On the client, within media portal configuration, under TV settings...
Hi folks. I have an issue with a new install/integration into my mediaportal system. I have a “mediaportal server” which has the TV...
Ran into this problem following an otherwise sucessful upgrade from MP 1.34 x64 to MP 1.35 x64 the CEC Remote plugin which I use just to control volume and standby, will no longer put my devices (TV & AVR) to sleep when the HTPC is put in standby. Also when I wake up the HTPC MP closes or crashes (not sure which) as per the example in...
Ran into this problem following an otherwise sucessful upgrade from MP 1.34 x64 to MP 1.35 x64 the CEC Remote plugin which I use...
Ran into this problem following an otherwise sucessful upgrade from MP 1.34 x64 to MP 1.35 x64 the CEC Remote plugin which I use...
Many thanks for the answer.
So far I've used Logitech's Harmony hub. This allows you to control all components (including the media portal). I have now contacted the Sofabaton hotline. It should also work here like with the Harmony. Unfortunately, not all of the IR codes are correct. You can also learn commands here. But that doesn't...
Many thanks for the answer.
So far I've used Logitech's Harmony hub. This allows you to control all components (including the...
I don't have a complicated A/V system - a Sony A8H TV, Yamaha receiver, and a HTPC on which I run most media through MediaPortal. I...
Default Direct Sound Device was the problem.
MPAR worked better than Dircect Sound, but is still a problem.
Changed Audio Renderer to use the TV and it's working.
Default Direct Sound Device was the problem.
MPAR worked better than Dircect Sound, but is still a problem.
Changed Audio Renderer...
New computer build with Windows 11 Pro.
MediaPortal 1.34 x64.
When I pause a video the audio drops out. This only occurs when...