Channel Change Delay (1 Viewer)

JonnyCam

Portal Member
January 27, 2006
7
0
Is there anyway that I can make the usbuirt slow down on it's button pressing?

The key press for a 2 digit channel has no real gap between the commands, and my cable box seems to have issues picking these up.

Thanks
 

SteveV

Retired Team Member
  • Premium Supporter
  • October 13, 2005
    340
    0
    Boston, Massachusetts USA
    JonnyCam said:
    Is there anyway that I can make the usbuirt slow down on it's button pressing?

    The key press for a 2 digit channel has no real gap between the commands, and my cable box seems to have issues picking these up.

    Thanks

    Not sure which version of MP you're using, but assuming it's RC 0.20 (or a more recent CVS build) you can control the delay between commands as follows:

    Launch Configuration.exe and select Remote-->USBUIRT and adjust the "Inter command delay ms" value.

    Steve
     

    Users who are viewing this thread

    Similar threads

    Hello, i'm absent from MP forum since a while now, looking your logs, your video is 23.96Hz, but your screen is already in 25hz, and after try to enable 50Hz ? So, MP detecte 23 hz and want to switch TV to 25 hz, but can't and MP want switch to 50hz try to start change frequency before MP Start, on windows parameter. i remember...
    Hello, i'm absent from MP forum since a while now, looking your logs, your video is 23.96Hz, but your screen is already in 25hz...
    After finally managing to get DRR working on my Intel Integrated Graphics 630 based setup, which was down to the default ON setting...
    Replies
    3
    Views
    859
    I've been using version 1.2.2.0 for years and have found no need to upgrade to newer version. I hate it that skins loose compatibility with almost every new version. And new skins are too 'fancy' for my taste. I use a customized version of the default wide skin with only Videos and TV in the main menu. I use mediaportal for recording...
    I've been using version 1.2.2.0 for years and have found no need to upgrade to newer version. I hate it that skins loose...
    I've been using version 1.2.2.0 for years and have found no need to upgrade to newer version. I hate it that skins loose...
    Replies
    0
    Views
    991
    This seem to happen only occasingly for some users. I never saw it for example with my windows 10 system. As you said it doesn't cause any mis-functionality, it is just annoying. It's on the bugfix agenda for next MP2.4 release. That's correct, there are two options: Using the navigation buttons or the mouse wheel. It's also...
    This seem to happen only occasingly for some users. I never saw it for example with my windows 10 system. As you said it doesn't...
    I am using Windows 7, Media Portal 2.32, WMC skin and have 5 satellite TV cards installed. The only error I get when I start Media...
    Replies
    3
    Views
    723
    For me it is not momentary i.e.when I press play/pause or stop the red dot appears and stays there and presumably has scheduled a recording, pressing either button again turns the red dot off and cancels the recording. I did not try with the number buttons, I am running MP 1.29.
    For me it is not momentary i.e.when I press play/pause or stop the red dot appears and stays there and presumably has scheduled a...
    I recollect someone else reporting this problem, but I cannot now find the relevant post. In this thread I want describe the...
    Replies
    15
    Views
    3K
    Good job, nice release as usual (y)
    Good job, nice release as usual (y)
    We are proud to present MediaPortal 2.4 MediaPortal 2.4 is a full-blown media center software that addresses most common user...
    Replies
    5
    Views
    2K
    Top Bottom